iE 350 PLC https://deif-staging.jcdhotel.dk/products/ie-350-plc/ Programmable automation PLC controller with build-in 3-phase measurement en Thu, 18 Jun 2026 05:13:09 GMT Active 0e2b9c4f-923a-4677-b947-5fa41fb695e2 The iE 350 PLC's modular I/O with 3-phase grid measurement ensures maximum design flexibility, and the cutting-edge cyber security features make it a safe choice for tomorrow's intelligent energy solutions for both land and marine applications.

]]> Advanced Features of the iE 350 PLC Controller

The iE 350 PLC Controller is designed to meet the demands of modern energy management systems. With its modular I/O and 3-phase grid measurement, it ensures maximum design flexibility. The cutting-edge cyber security features make it a safe choice for both land and marine applications. The controller is fully functional from -40 °C, making it ideal for harsh environments. Its robust design includes superior bump, shock, and vibration resistance properties, ensuring reliable operation and transportation.

Why Choose the iE 350 PLC Controller?

Choosing the iE 350 PLC Controller means opting for a flexible, service-friendly solution. Its native EtherCAT fieldbus supports several hundreds of I/O points through a modular concept with distributed nodes. The fully open Linux software platform provides full access to system setup, and the controller supports IEC 61131-3 programming for easy configuration. With remote configuration and visualization capabilities, the iE 350 PLC Controller offers complete freedom and ease of use.

Robust right out of the box

The iE 350 PLC is designed to get the job done, even in harsh conditions. Fully functional from -40 °C, the controller can start-up by self-heating and control and do surveillance of auxiliary equipment from this extreme temperature. The base-mounted rack and sturdy metal cabinet give it superior bump, 50G shock, and vibration resistance properties during operation and transportation. For example, the rack is mounted with a large screw on the switchboard's back plate, so that the unit cannot fall off the DIN rails after transportation.

The flanges ensure improved grounding, increasing protection against electrical disturbances. The backplane interconnection of the I/O modules ensures reliable communication in harsh environments. Built-in components provide efficient protection of power supply and I/O circuits against lightning impacts. The iE 350 PLC is immune to ESD bursts at a level conforming to international standards, reducing the risk of damaged terminals.

All units are fully production tested and verified at the factory through HALT (Highly Accelerated Life Testing), and the Linux-based platform provides fail-safe and robust system software. These and other features add up to a lifetime of at least 10 years for the iE 350 PLC, plus supreme robustness which reduces service and downtime costs.

Flexible solution design options

The modular architecture of the iE 350 PLC allows you to use it for compact, flexible, and service-friendly solutions – from simple plug-and-play rack modules to cabling with pluggable connectors. Its native EtherCAT fieldbus supports several hundreds of I/O points through a modular concept with distributed nodes based on EtherCAT and supporting EtherCAT cable redundancy. As a result, you have complete freedom to place multiple I/O nodes in different physical locations to reduce cabling, and the built-in 5-port switch of the PCM3.1 module can be configured with individual VLANs, saving the cost of external equipment.

The fully open Linux software platform gives you full access to system setup, and you can take advantage of the great amounts of Linux documentation and support available online. The controller is based on CODESYS V3 and supports IEC 61131-3 programming. This ensures easy programming and configuration, and you can easily reuse existing PLC code if converting from other PLC solutions, giving you complete freedom to choose your preferred hardware vendor. You can configure the iE 350 PLC remotely using a browser. The device is discoverable using its host name, and remote visualisation is possible via TCP/IP.

Despite these flexible hardware and software options, installing the iE 350 PLC is very easy: It comes pre-assembled in racks according to your configuration requirements. You do not have to assemble the controller yourself and can complete your sourcing process without assembly and testing.

Performance and system design freedom

The high-speed EtherCAT fieldbus on the iE 350 PLC is fast enough to handle distributed I/O with one main controller and hundreds of distributed analogue and digital I/O and communication channels in multiple locations. You get the same update speed for local and distributed I/O nodes in an external network.

The system software launches very quickly and offers fail-safe start-up with two operating system images separated from the application. If one image fails to start up the iE 350 PLC, the controller falls back to the other image and completes start-up. Each image can be updated remotely. After a successful start-up after an image update, the new image can be set as active. The iE 350 PLC uses a special file system that tolerates sudden loss of power and monitors itself for errors.

The high-performance features of the iE 350 PLC also include direct 690 VAC 3-phase grid measurement, allowing you to measure voltage and frequency in a wide range from 2 to 897 VAC.

Built-in operational cyber security features

With connected and online controllers, operational security is critical. The Linux system in the iE 350 PLC provides cutting-edge security features. For example, boot and firmware updates can only be carried out with signed update packages. By default, there is only one user (admin) account on the iE 350 PLC. Still, you can create and manage multiple users and access rights to ensure that the necessary users can handle the unit while protecting theiE 350 PLC from unauthorised access.

CODESYS web visualisation is managed through certificate handling via the system web page. Authentication keys are added via system web configuration, and the iE 350 PLC builds on standard secure file transfer and access protocols like SSH and SCP. Finally, the Linux system is less vulnerable to ordinary computer virus attacks than Windows-based PLCs.

Service-friendly, now and in future

With a design lifetime of no less than 10 years, the iE 350 PLC is with you for the long haul. Combined with its robust construction and reliable performance, you get years of uninterrupted operation with little need of service, maintenance, or repairs. If spare parts do become necessary, we have you covered: The iE 350 PLC uses few spare parts thanks to its modular and multi-functional architecture, and new parts can be supplied quickly if needed. We offer a 10-year spare part supply warranty so you can keep your parts stock up to date.
All software updates are handled by the iE 350 PLC itself with no need of user intervention. No special tools are required; the new software update files are uploaded via the system web configuration pages.
Like all other DEIF products, the iE 350 PLC comes with our 2-year warranty (not including wear parts) which can optionally be prolonged to 3 years.

Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.

]]> 19811 eedcbb74-92d0-48ea-a2fb-bc5fe1cc6baf https://deif-staging.jcdhotel.dk/products/modules/governor-and-avr/gam31/ This governor and AVR module has four relay outputs, two analogue outputs and a pulse width modulation output, and two analogue inputs.

]]> This governor and AVR module has four relay outputs, two analogue outputs and a pulse width modulation output, and two analogue inputs. These I/Os are configurable. GAM3.1 also has terminals for analogue load sharing (future use).

]]> Physical connections
  • 4 x Relay output—configurable
    • 30 V DC, and 6 A
  • 1 x Active power (P) (kW) load sharing (future use)
    • -5 to 5 V DC
  • 1 x Reactive power (Q) (kVAR) load sharing (future use) 
    • -5 to 5 V DC
  • 2 x Analogue current or voltage output (analogue current or voltage output)—Active outputs
    • -20 to 20 mA, or 0 to 20 mA, or 4 to 20 mA, or any custom range between -25 and 25 mA
    • Voltage output (DC)-10 to 10 V, 0 to 10 V, 0 to 5 V, -5 to 5 V, 0 to 3 V, -3 to 3 V, or 0 to 1 V, or any custom range between -10 and 10 V
  • 1 x Pulse width modulation (PWM) output
    • 500 Hz ±50 Hz
    • Voltage: Low level: < 0.5 V. High level: > 5.5 V. Maximum: 6.85 V.
  • 2 x Analogue current or voltage input configurable (galvanically connected)
    • From active transmitter: 0 to 20 mA, 4 to 20 mA, or any custom range between 0 and 24 mA
    • Voltage inputs (DC) -10 to 10 V, 0 to 10 V, or any custom range between -10 and 10 V
]]> 19821 36eaf14f-a8d5-43d9-ba36-2388c74bf035 https://deif-staging.jcdhotel.dk/products/modules/governor-and-avr/gam32/ This governor and AVR module has its own power supply, two analogue outputs and a pulse width modulation output, five digital inputs, a status relay output, and four relay outputs

]]> This governor and AVR module has its own power supply, two analogue outputs and a pulse width modulation output, five digital inputs, a status relay output, and four relay outputs. Apart from the status relay, all these I/Os are configurable. GAM3.2 has its own microprocessor. If the rack power supply fails, GAM3.2 can continue to be used for manual operation if it has its own, independent power supply. The power supply terminals include circuit protection against load dump transients and JEM177 surge transients (rugged design). These terminals also include battery voltage measurement.

]]> Physical Connections
  • Supply
    • 12 or 24V DC Power supply and frame ground
  • 2 x Analogue current or voltage output 
    • Active—GOV/AVR/configurable
    • Current output: any custom range between -25 and 25 mA
    • Voltage output (DC)-10 to 10 V
  • 1 x Pulse width modulation (PWM) output
    • 500 Hz ±50 Hz
    • Voltage: Low level: < 0.5 V. High level: > 5.5 V. Maximum: 6.85 V.
  • 5 x Digital inputs—configurable (Bipolar)
    • ON: -36 to -8 V DC, and 8 to 36 V DC
    • OFF: -2 to 2 V DC
    • Voltage withstand: ±36 V DC
  • 1 x Relay output—GAM3.2 status
    • Solid State
    • 30 V DC and 1 A
  • 4 x Relay outputs—configurable
    • 30 V DC, and 6 A

Supply voltage low alarm

  • This default alarm is for auxiliary power supply voltage protection.
  • The alarm is based on the power supply voltage measured by the GAM. The alarm is activated when the power supply voltage is less than the setpoint for the delay time.

Supply voltage high alarm

  • This default alarm is for auxiliary power supply voltage protection.
  • The alarm is based on the power supply voltage measured by the GAM. The alarm is activated when the power supply voltage exceeds the set point for the delay time.
]]> 19793 7d76ae16-9f70-4efa-84fa-408fd80f94d1 https://deif-staging.jcdhotel.dk/products/modules/power/psm31/ The PSM3.1 power supply module provides power to all the hardware modules in the primary controller rack containing the main controller.

]]> The PSM3.1 power supply module provides power to all the hardware modules in the primary controller rack containing the main controller. The module communicates with extension racks through use of the dedicated DEIF internal communication ports. 

The primary controller rack status and alarms activate the PSM's three relay outputs. There are two ports for internal communication with I/O extension units. PSM3.1 manages the hardware module self-checks for the rack and includes a power LED. The power supply terminals include circuit protection against load dump transients and JEM177 surge transients (rugged design). These terminals also include battery voltage measurement.

]]> Physical connections
  • Supply
    • 12 or 24V DC Power supply and frame ground
  • 3 x Relays outputs 
    • 30V DC, 1A
    • 1 × Status OK (fixed), and 2 × configurable
  • 2 x RJ45 
    • DEIF internal communications ports 

Protection

  • The power supply inputs are internally protected by a 12 A fuse (not replaceable) (fuse size determined by load dump requirements).

Supply voltage low alarm

  • The alarm is activated when the power supply voltage is less than the setpoint for the delay time.

Supply voltage high alarm

  • The alarm is activated when the power supply voltage exceeds the set point for the delay time.

Power supply voltage as an analogue output

  • You can configure an analogue output with a function for the power supply voltage. The controller then adjusts the analogue output to reflect the operating value.
]]> 19828 983ba502-eda5-4099-a679-8c4da578d983 https://deif-staging.jcdhotel.dk/products/modules/power/psm32/ A PSM 3.2 power supply module is installed in each extension rack to provide power to all the hardware modules in the extension rack.

]]> A PSM 3.2 power supply module is installed in each extension rack to provide power to all the hardware modules in the extension rack. It communicates with the primary controller rack and other extension racks through the use of the dedicated DEIF internal communication ports.

The extension rack status and alarms activate the PSM's three relay outputs. There are two ports for internal communication with the main controller. PSM3.2 manages the hardware module self-checks for the rack and includes a power LED. The power supply terminals include circuit protection against load dump transients and JEM177 surge transients (rugged design). These terminals also include battery voltage measurement.

]]> Physical connections
  • Supply
    • 12 or 24V DC Power supply and frame ground
  • 3 x Relays outputs 
    • 30V DC, 1A
    • 1 × Status OK (fixed), and 2 × configurable
  • 2 x RJ45 
    • DEIF internal communications ports 

Protection

  • The power supply inputs are internally protected by a 12 A fuse (not replaceable) (fuse size determined by load dump requirements).

Supply voltage low alarm

  • The alarm is activated when the power supply voltage is less than the setpoint for the delay time.

Supply voltage high alarm

  • The alarm is activated when the power supply voltage exceeds the set point for the delay time.

Power supply voltage as an analogue output

  • You can configure an analogue output with a function for the power supply voltage. The controller then adjusts the analogue output to reflect the operating value.
]]> 19785 40ba01dd-7c89-41f1-bbaa-25d199d19049 https://deif-staging.jcdhotel.dk/products/modules/input-output/iom31/ The input/output module has four changeover relay outputs and 10 digital inputs. These I/Os are all configurable.

]]> The input/output module has four changeover relay outputs and 10 digital inputs. These I/Os are all configurable.

]]> Physical connections
  • 4 x Relay outputs—configurable
    • 250 V AC or 30 V DC, and 6 A
  • 10 x Digital inputs—configurable (Bipolar)
    • ON: -36 to -8 V DC, and 8 to 36 V DC
    • OFF: -2 to 2 V DC
    • Voltage withstand: ±36 V DC
]]> 19799 a27e0648-d4ab-4a40-bca3-7101b723acde https://deif-staging.jcdhotel.dk/products/modules/input-output/iom33/ The input output module has ten analogue multifunctional inputs. These I/Os are all configurable.

]]>
  • 10 x multifunctional inputs, freely selectable as:
  • Digital input with wire break
  • 0(4)…20 mA
  • ±10V DC/ 0…10V DC
  • Resistor input (RMI), 1, 2- or 3-wire
  • Pt100
  • Pt1000
  • Thermocouple, type E, J, K, N, R, S, T selectable    

    • For all inputs: Voltage withstand ±36V DC     

    ]]>         19816 fe268532-2a3d-4c2b-97af-c042e93af80a https://deif-staging.jcdhotel.dk/products/modules/input-output/iom32/ The input output module has four relay outputs, four analogue multifunctional outputs (including two pulse width modulation PWM outputs), four digital inputs, and four analogue multifunctional inputs. These I/Os are all configurable.

    ]]>
  • 4 x Solidstate relay outputs – configurable (30 V DC, 6 A, resistive)
  • 2 x Analogue multifunctional output (mA, V DC, PWM)
  • 2 x Analogue multifunctional output (mA, V DC)
  • 4 x Digital input
    ON: -36 to -8 V DC, and 8 to 36 V DC
    OFF: -2 to 2 V DC
    Voltage withstand: ±36 V DC
  • 4 x Analogue multifunctional input (mA, V DC, Resistor (RMI))
    • ]]>         19822 6913261d-e0c5-4fae-80b3-45b8a7a4b880 https://deif-staging.jcdhotel.dk/products/modules/input-output/iom34/ The input/output module has 12 transistor outputs and 16 digital inputs. These I/Os are all configurable.

    ]]>     The input/output module has 12 transistor outputs and 16 digital inputs. These I/Os are all configurable.

    The controller can use transistor outputs for many purposes. Examples: Activate alarm devices, open and close breakers, and genset speed and voltage regulation.

    ]]>     Physical connections
    • Supply
      • Positive supply for transistor terminals (12 or 24 V DC)
    • 12 x transistor outputs (Configurable)
      • PNP—Transistor output (< 55 °C: 250 mA; > 55 °C: 200 mA)
    • 16 x digital inputs. (Configurable)
      • ON: -36 to -8 V DC, and 8 to 36 V DC
      • OFF: -2 to 2 V DC
      • Voltage withstand: ±36 V DC

    Transistor output characteristics and configuration

    • All transistor outputs are configurable. You can assign a digital output function, or configure one alarm, for a transistor output. You can program customized transistor output functions using CustomLogic (PICUS software). You can also create customized digital output functions using CustomLogic, and assign a transistor output.
    • The transistor hardware itself is normally open. The transistor output state (whether it is open or closed) depends on the configuration in software and the function (or alarm) state. 

    Digital input characteristics

    • IOM3.4 has two independent groups of digital inputs with separate common terminals.
    ]]>         19805 d9b4c8f7-f1f3-4ec3-87cc-26f35ec445db https://deif-staging.jcdhotel.dk/products/modules/engine-interface/eim31/ The engine interface module has its own power supply and a tach input to measure speed. It also has four relay outputs, four digital inputs, and three analogue inputs. These I/Os are configurable.

    ]]>     The engine interface module has its own power supply and a tach input to measure speed. It also has four relay outputs, four digital inputs, and three analogue inputs. These I/Os are configurable.

    The power supply terminals include circuit protection against load dump transients and JEM177 surge transients (rugged design).

    ]]>     Physical Connections
    • Supply
      • 12 or 24V DC Power supply and frame ground
    • 3 x Relay output—Configurable
      • 30 V DC, and 6 A
    • 1 x Relay output with wire break detection*- configurable
      • 30 V DC, and 6 A
    • 4 x Digital inputs—configurable (Bipolar
      • ON: -36 to -8 V DC, and 8 to 36 V DC
      • OFF: -2 to 2 V DC
      • Voltage withstand: ±36 V DC
    • 1 x Magnetic pickup with wire break detection* **
      • 3 to 70 V AC peak
      • 2 to 20,000 Hz
      • Can be useful during start-up, when the generator frequency is too low to be a reliable indication of genset speed 
    • 1 x Generator tach input or NPN/PNP sensor **
      • 8 to 36 V DC
      • 2 to 20,000 Hz
      • Typically signal from one of the phases of the generator.
      • Can be useful during start-up, when the generator frequency is too low to be a reliable indication of genset speed 
    • 3 x Analogue current or resistance measurement inputs (RMI)—configurable
      • Current standard 0 to 20 mA, 4 to 20 mA or configurable 0 to 25 mA
      • Pt100/1000 -40 to 250 °C (-40 to 482 °F)
      • Resistance Any custom range between 0 and 2.5 kΩ
      • Digital input Dry contact with cable supervision maximum 330 Ω for ON detection

    Supply voltage low alarm

    • The alarm is activated when the power supply voltage is less than the setpoint for the delay time.

    Supply voltage high alarm

    • The alarm is activated when the power supply voltage exceeds the set point for the delay time

    Magnetic pickup wire break

    • This alarm is for magnetic pickup wire break. If the engine is running, but there is no pulse for 2 seconds, then the controller monitors the cable. If there is no change during the alarm delay time, then the controller activates the alarm.

    Auxiliary power supply voltage as an analogue output

    • You can configure an analogue output with a function for the auxiliary power supply voltage. The controller then adjusts the analogue output to reflect the operating value.
    • An analogue output with the power supply voltage may be wired to a switchboard instrument. The operator can then see if the auxiliary power supply fails.

    *Note: These inputs cannot both be used at the same time.

    **Note You cannot use both the MPU and tach input at the same time

    All analogue multi-functional inputs for EIM3.1 have a common ground

    ]]>         19809 e7d6a9be-5db8-486f-a84a-2b00bb57a2f3 https://deif-staging.jcdhotel.dk/products/modules/alternating-current/acm31/ The alternating current module measures the voltage and current on one side of a breaker, and the voltage on the other side. The hardware module responds when the measurements exceed the AC alarm parameters.

    ]]>     The alternating current module measures the voltage and current on one side of a breaker, and the voltage on the other side. The hardware module responds when the measurements exceed the AC alarm parameters. ACM3.1 uses the AC measurements to check the synchronization before the breaker closes.

    ACM3.1 provides robust frequency detection in environments with electrical noise. ACM3.1 allows extended measurement bandwidth up to 40 times the nominal frequency. ACM3.1 includes a configurable 4th current measurement.

    Default: ACM3.1 measures 3-phase systems. Optional: Select split-phase (1-phase, 3-wire, for example, L1-N-L2) or single-phase (1-phase, 2-wire, for example, L1-N)

    ]]>     Physical connections

    • 2 × 3-phase voltage measurements (L1, L2, L3 and N)
      • 100 to 690 V AC phase-to-phase (nominal)
    • 1 × 3-phase current measurement and 4th current measurement ((L1, L2, L3 and 4th)
      • 1 or 5 A, AC (nominal)

    Voltage measurement characteristics 

    • The ACM has two sets of terminals for voltage measurement. The first set of terminals measures the voltage on the busbar. The second set of terminals measures the voltage from the source. The ACM uses these measurements for logging, alarms and protective functions.

    Current measurement characteristics

    • The ACM measures the current, then uses these measurements for logging, alarms and protective functions.

    Power measurements

    • For power functions, the second set of voltage measurements and the current measurements from the ACM are used together.

    Frequency measurements

    • Provides robust frequency detection in environments with electrical noise.
    ]]>         19817 0c81b3cd-00c7-4b74-9429-2bc10c289284 https://deif-staging.jcdhotel.dk/products/modules/alternating-current/acm32/ The alternating current module 3.2 measures the phase currents on the consumer side and neutral side of a generator. The ACM3.2 uses the measurements to detect phase-to-phase faults or phase-to-earth faults in earthed generator systems.

    ]]>     The alternating current module 3.2 measures the phase currents on the consumer side and neutral side of a generator. The ACM3.2 uses the measurements to detect phase-to-phase faults or phase-to-earth faults in earthed generator systems. The protection consists of:

    • A stabilized stage that uses a dual-slope operating characteristic. This current restraint approach is also known as biased differential protection.
    • A high set differential stage (non-stabilized).
    • Protection includes ANSI 87G differential protection for generators
    ]]>     Physical connections
    • 1 × 3-phase current measurement consumer side
      • 1 or 5 A AC (nominal)
    • 1 × 3-phase current measurement neutral side 
      • 1 or 5 A AC (nominal)

    Current measurement characteristics

    The ACM3.2 has two sets of terminals for current measurement. 

    • The first set of terminals measures the current at the consumer side of the generator. 
    • The second set of terminals measures the current at the neutral side of the generator. 
    • The ACM3.2 uses these measurements for logging, alarms and protective functions relating to differential current protection in the system.

    Frequency measurements

    • Provides robust frequency detection in environments with electrical noise.

    Protection

    • ANSI 87G differential protection for generators
    ]]>         24062 4dc8428d-4335-4587-9d24-40f36d074f83 https://deif-staging.jcdhotel.dk/products/modules/computing/pcm33/ Housed in the primary controller rack, the processor and communication module contains the controller's main microprocessor, which runs the controller application software.

    ]]>     Housed in the primary controller rack, the processor and communication module contains the controller's main microprocessor, which runs the controller application software. It includes the Ethernet switch to manage the controller Ethernet connections, with four 100BASE-TX Ethernet connections. It has a Self-check OK LED. It also contain 4 sets of CAN bus terminals, 2 sets RS422/RS-485 terminals and USB storage port. The PCM3.3 performs time synchronization with and NTP server.

    ]]>     Physical connections
    • 4 x 100BASE-TX Ethernet
      • DEIF network
      • SCADA
      • Alarm Monitoring System
      • Modbus TCP/IP
      • Service PC
      • Display unit
      • Configurable
    • 4 x CAN bus
    • 2 x RS-422/RS 485

    Controller temperature too high

    • This is a built-in alarm for the controller internal temperature, as measured on PCM3.3

    PCM3.3 clock battery

    • PCM3.3 includes an internal battery for timekeeping during a power supply failure. If there is no power supplied to the controller or the PCM module, the controller uses the battery power for its internal clock.
    • The PCM clock battery failure alarm is activated when the battery in PCM3.3 needs to be replaced
    ]]>         CE DoC 4910290104 UK.pdf https://deif-cdn-umbraco.azureedge.net/media/2ebnavm3/ce-doc-4910290104-uk.pdf?rnd=134127004733170000&v=9 55d002f9-949d-40aa-95de-9d8a3911c3c3 PPM_300 Mon, 12 Jan 2026 14:07:53 GMT 2026-01-12T14:07:53+00:00 2026-01-12T14:07:53+00:00 eng document J Approvals/Certifications iE 350 PLC Data sheet 4921240659 UK.pdf https://deif-cdn-umbraco.azureedge.net/media/k5kfyrmv/ie-350-plc-data-sheet-4921240659-uk.pdf?rnd=134122595381130000&v=9 454cd54f-a495-480e-8851-58c1ad7f5790 iE_350_PLC Wed, 07 Jan 2026 11:38:58 GMT 2026-01-07T11:38:58+00:00 2026-01-07T11:38:58+00:00 eng document I Data Sheet UL CoC E339342-20140927 - UL Listed (2025-11) UK.pdf https://deif-cdn-umbraco.azureedge.net/media/iban3rwl/ul-coc-e339342-20140927-ul-listed-2025-11-uk.pdf?rnd=134106271302800000&v=9 c6de4058-d1cb-43b5-963b-993f2a0aba45 iE_350 Fri, 19 Dec 2025 14:12:10 GMT 2025-12-19T14:12:10+00:00 2025-12-19T14:12:10+00:00 eng document A Approvals/Certifications UL CoC E314309-20140627 - UL Listed (2025-05) UK.pdf (1) https://deif-cdn-umbraco.azureedge.net/media/qubdfdng/ul-coc-e314309-20140627-ul-listed-2025-05-uk.pdf?rnd=134106269026370000&v=9 8d32029d-6fa6-4ae5-b9c8-0d58ccb9bc18 iE_350 Fri, 19 Dec 2025 14:08:22 GMT 2025-12-19T14:08:22+00:00 2025-12-19T14:08:22+00:00 eng document A Approvals/Certifications DNV TAA00003FC UK.pdf https://deif-cdn-umbraco.azureedge.net/media/k5zifs1c/dnv-taa00003fc-uk.pdf?rnd=134100413407270000&v=9 cb82f24f-b762-42a8-af5c-122843132546 iE_350_MARINE Fri, 12 Dec 2025 19:29:00 GMT 2025-12-12T19:29:00+00:00 2025-12-12T19:29:00+00:00 eng document B Approvals/Certifications RINA ELE060325XP UK - Cyber Security.pdf https://deif-cdn-umbraco.azureedge.net/media/eqqohsqv/rina-ele060325xp-uk-cyber-security.pdf?rnd=134096591033470000&v=9 cae3203c-7e15-4e9e-bc4c-48f3b80c1a14 iE_250 Mon, 08 Dec 2025 09:18:23 GMT 2025-12-08T09:18:23+00:00 2025-12-08T09:18:23+00:00 eng document A Approvals/Certifications iE 350 PLC Installation instructions 4189341390 UK.pdf https://deif-cdn-umbraco.azureedge.net/media/4bxj000m/ie-350-plc-installation-instructions-4189341390-uk.pdf?rnd=134087261108200000&v=9 6b9d6ee8-684c-463d-8cca-52ed61d41cdd iE_350_PLC Thu, 27 Nov 2025 14:08:30 GMT 2025-11-27T14:08:30+00:00 2025-11-27T14:08:30+00:00 eng document G Installation Instructions CCS GB25PTB00023 - Cyber Security UK.pdf https://deif-cdn-umbraco.azureedge.net/media/xeoeup1d/ccs-gb25ptb00023-cyber-security-uk.pdf?rnd=134066383182200000&v=9 3f4a1ca1-7363-4ddc-8524-a8650fffb43c iE_350_MARINE Mon, 03 Nov 2025 10:11:58 GMT 2025-11-03T10:11:58+00:00 2025-11-03T10:11:58+00:00 eng document A Approvals/Certifications iEx50 E27 Recovery Plan UK.pdf https://deif-cdn-umbraco.azureedge.net/media/cniabyhs/iex50-e27-recovery-plan-uk.pdf?rnd=134051845330700000&v=9 e000500b-9cf2-41ce-a463-a8733d98f9f5 iE_250 Fri, 17 Oct 2025 14:22:13 GMT 2025-10-17T14:22:13+00:00 2025-10-17T14:22:13+00:00 eng document A Approvals/Certifications General safety note 4189341189 UK-FR.pdf https://deif-cdn-umbraco.azureedge.net/media/t3ofzpjw/general-safety-note-4189341189-uk-fr.pdf?rnd=134045044194400000&v=9 bd5c5d87-9036-4df9-881e-cc1bd5ed3b40 MDR-2 Thu, 09 Oct 2025 17:26:59 GMT 2025-10-09T17:26:59+00:00 2025-10-09T17:26:59+00:00 eng document C Other Technical Documentation LR LR2024766TA-03 - Cybersecurity UK.PDF https://deif-cdn-umbraco.azureedge.net/media/x0lnvzad/lr-lr2024766ta-03-cybersecurity-uk.pdf?rnd=134003267570970000&v=9 e4ca97a6-6403-4cbb-b19a-b9e78b9993e4 iE_350_MARINE Fri, 22 Aug 2025 08:59:17 GMT 2025-08-22T08:59:17+00:00 2025-08-22T08:59:17+00:00 eng document C Approvals/Certifications ABS 25-0283426-PDA Cybersecurity UK.pdf https://deif-cdn-umbraco.azureedge.net/media/fosa44nk/abs-25-0283426-pda-cybersecurity-uk.pdf?rnd=134000679398630000&v=9 790fa433-eaaa-4e49-b36f-057dee78bf0f iE_250 Tue, 19 Aug 2025 09:05:39 GMT 2025-08-19T09:05:39+00:00 2025-08-19T09:05:39+00:00 eng document A Approvals/Certifications BV 80626 A0 BV - Cybersecurity UK.pdf https://deif-cdn-umbraco.azureedge.net/media/etdihbkw/bv-80626-a0-bv-cybersecurity-uk.pdf?rnd=133973005213830000&v=9 8583c63c-3a56-4f14-a467-341dcbf4cb0f iE_250_MARINE Fri, 18 Jul 2025 08:22:01 GMT 2025-07-18T08:22:01+00:00 2025-07-18T08:22:01+00:00 eng document A Approvals/Certifications BV 80121 A1 BV - Cybersecurity UK.pdf https://deif-cdn-umbraco.azureedge.net/media/sxajtqm3/bv-80121-a1-bv-cybersecurity-uk.pdf?rnd=133971465137030000&v=9 c199c08d-439d-45d1-98ba-7ad024d2cceb iE_650_PLC Wed, 16 Jul 2025 13:35:13 GMT 2025-07-16T13:35:13+00:00 2025-07-16T13:35:13+00:00 eng document B Approvals/Certifications ABS 25-0278636-1-1-PDA UK.PDF https://deif-cdn-umbraco.azureedge.net/media/qgpd52q2/abs-25-0278636-1-1-pda-uk.pdf?rnd=133971461543800000&v=9 f23f9f99-fb1c-4f60-9091-c21f253348b6 PPM_300 Wed, 16 Jul 2025 13:29:14 GMT 2025-07-16T13:29:14+00:00 2025-07-16T13:29:14+00:00 eng document A Approvals/Certifications Rack and module 2D CAD drawings.zip https://deif-cdn-umbraco.azureedge.net/media/42aflssd/rack-and-module-2d-cad-drawings.zip?rnd=133909096380300000&v=9 ca5500ef-f843-499b-adec-3fd17c235398 iE_350 Mon, 05 May 2025 09:07:18 GMT 2025-05-05T09:07:18+00:00 2025-05-05T09:07:18+00:00 eng document B Drawings Module 3D STEP-files.zip https://deif-cdn-umbraco.azureedge.net/media/mqqb0o53/module-3d-step-files.zip?rnd=133864375685900000&v=9 3b1d207c-38fd-471a-b424-49ddbaf8fbe7 iE_350 Fri, 14 Mar 2025 14:52:48 GMT 2025-03-14T14:52:48+00:00 2025-03-14T14:52:48+00:00 eng document A Drawings Rack 2D PDFs.zip https://deif-cdn-umbraco.azureedge.net/media/3bafvz31/rack-2d-pdfs.zip?rnd=133864375169270000&v=9 e75a41f0-bdbb-4916-b68d-1d29a2a2ae7b iE_350 Fri, 14 Mar 2025 14:51:56 GMT 2025-03-14T14:51:56+00:00 2025-03-14T14:51:56+00:00 eng document A Drawings Rack and module 3D PDFs.zip https://deif-cdn-umbraco.azureedge.net/media/jzdgxwz0/rack-and-module-3d-pdfs.zip?rnd=133864374192800000&v=9 db6b4656-cf3a-4b83-9323-aeca2bf83529 iE_350 Fri, 14 Mar 2025 14:50:19 GMT 2025-03-14T14:50:19+00:00 2025-03-14T14:50:19+00:00 eng document A Drawings Rack and module 3D STEP-files.zip https://deif-cdn-umbraco.azureedge.net/media/bprh432z/rack-and-module-3d-step-files.zip?rnd=133864373701330000&v=9 777fe213-8d99-4934-964a-8cc0dd0f0fa7 iE_350 Fri, 14 Mar 2025 14:49:30 GMT 2025-03-14T14:49:30+00:00 2025-03-14T14:49:30+00:00 eng document A Drawings Rack and module SVGs.zip https://deif-cdn-umbraco.azureedge.net/media/ycan4dnw/rack-and-module-svgs.zip?rnd=133864291718370000&v=9 0ddf81d8-ecb6-4338-bf68-8908b91a5b87 iE_350 Fri, 14 Mar 2025 12:32:51 GMT 2025-03-14T12:32:51+00:00 2025-03-14T12:32:51+00:00 eng document A Drawings Rack and module PNGs.zip https://deif-cdn-umbraco.azureedge.net/media/0tji2cej/rack-and-module-pngs.zip?rnd=133864290818930000&v=9 088ed2cc-1a89-48c5-b1a7-012c3af2ce4d iE_350 Fri, 14 Mar 2025 12:31:21 GMT 2025-03-14T12:31:21+00:00 2025-03-14T12:31:21+00:00 eng document A Drawings iE 7 Local display 3D STEP-file.zip https://deif-cdn-umbraco.azureedge.net/media/iwzdv0zv/ie-7-local-display-3d-step-file.zip?rnd=133819205160270000&v=9 eb3ab35d-d735-4f9f-9e2b-60ba550d9e0c iE_250 Tue, 21 Jan 2025 08:08:36 GMT 2025-01-21T08:08:36+00:00 2025-01-21T08:08:36+00:00 eng document A Drawings iE 7 Local display 3D PDF.pdf https://deif-cdn-umbraco.azureedge.net/media/u2dg2og2/ie-7-local-display-3d-pdf.pdf?rnd=133819204975300000&v=9 386e06bf-1fdc-4771-97d6-e195f2e5ba93 iE_250 Tue, 21 Jan 2025 08:08:17 GMT 2025-01-21T08:08:17+00:00 2025-01-21T08:08:17+00:00 eng document A Drawings iE 7 Local display 2D PDF.pdf https://deif-cdn-umbraco.azureedge.net/media/zjnjrpjp/ie-7-local-display-2d-pdf.pdf?rnd=133819204823300000&v=9 bd985ad2-df2f-4ec5-ae88-824345aca530 iE_250 Tue, 21 Jan 2025 08:08:02 GMT 2025-01-21T08:08:02+00:00 2025-01-21T08:08:02+00:00 eng document A Drawings iE 7 Local display 2D CAD drawing.dwg https://deif-cdn-umbraco.azureedge.net/media/1jppnj2p/ie-7-local-display-2d-cad-drawing.dwg?rnd=133819204629470000&v=9 a7e65fc2-e28f-482b-8a38-c7db0a70698a iE_250 Tue, 21 Jan 2025 08:07:42 GMT 2025-01-21T08:07:42+00:00 2025-01-21T08:07:42+00:00 eng document A Drawings DNV TAA00003G3 - Cybersecurity UK.pdf (2) https://deif-cdn-umbraco.azureedge.net/media/byzbr0cx/dnv-taa00003g3-cybersecurity-uk.pdf?rnd=133771853270970000&v=9 e8183316-ed57-4c4e-bbc3-41901f51b2e9 iE_250 Wed, 27 Nov 2024 12:48:47 GMT 2024-11-27T12:48:47+00:00 2024-11-27T12:48:47+00:00 eng document A Approvals/Certifications DNV TAA00003H9 UK.pdf https://deif-cdn-umbraco.azureedge.net/media/dnphhzry/dnv-taa00003h9-uk.pdf?rnd=133755431678130000&v=9 e6735e03-3d38-4642-8041-63ed1fa2443b iE_250 Fri, 08 Nov 2024 12:39:27 GMT 2024-11-08T12:39:27+00:00 2024-11-08T12:39:27+00:00 eng document A Approvals/Certifications UKCA DoC 4910290604 UK.pdf https://deif-cdn-umbraco.azureedge.net/media/duqb1yxp/ukca-doc-4910290604-uk.pdf?rnd=133743430663030000&v=9 e21d2105-e3ef-4eff-9acb-c8eb2b3d9e98 PPM_300 Fri, 25 Oct 2024 15:17:46 GMT 2024-10-25T15:17:46+00:00 2024-10-25T15:17:46+00:00 eng document B Approvals/Certifications iE350 PLC - v2.0.15.1 https://deif-staging.jcdhotel.dk/software/ie350-plc/2-0-15-1/ 82b0adaa-585f-4967-bb03-ec95d6fc5715 2025-12-29T00:00:00+00:00 software-version iE350 PLC 2.0.15.1 current Corrections
    • Fixed an issue where the Modbus TCP default port (502) was blocked by the firewall.
    ]]>         iE350 CODESYS TSP (SP20) - v1.3.2.2 (SP20) https://deif-staging.jcdhotel.dk/software/ie350-codesys-tsp-deprecated/1-3-2-2-sp20/ c7e39eb6-ef12-4389-a285-0372d91f6653 2025-02-07T00:00:00+00:00 software-version iE350 CODESYS TSP (SP20) 1.3.2.2 (SP20) current [1.3.2.2] - 2025-01-21

    Changes

    • Reversed the boolean level for negative input on iE 250 Local Digital IO.
    • In TSP,  the names Input Positive and Input Negative are used on iE 250 local Digital IO.


    [1.3.2.1] - 2025-01-15 Not Released

    New features

    • Added recipe folder under PLCLogic.

    Changes 

    • Changed FilePath to PLCLogic for PCM21, PCM33 and PCM62.
    • Made codesys-services wanted by custom-$variant.service.

    [1.3.2.0] - 2025-01-08 

    Added

    • Added CODESYS runtime v3.5.20.40.
    • Added info.json with CODESYS build information to PCM21, PCM33 and PCM62.
    • Increased persistent retain memory to 128KB for PCM21, PCM33, PCM62 and PCM61.
    • Added AIM61 devdesc 1.0.3.0, Revision=16#00000001.
    • Added AIM62 devdesc 1.0.3.0, Revision=16#00000001.
    • Added AIO61 devdesc 1.0.3.0, Revision=16#00000005.
    • Added AIO62 devdesc 1.0.3.0, Revision=16#00000001.
    • Added DIM61 devdesc 1.0.0.0, Revision=16#00000002.
    • Added DIO62 devdesc 1.0.0.0, Revision=16#00000002.
    • Added DOM61 devdesc 1.0.0.0, Revision=16#00000003.
    • Added DIM61 devdesc 1.0.1.0, Revision=16#00000002. 
    • Added DIO62 devdesc 1.0.1.0, Revision=16#00000002.
    • Added DOM61 devdesc 1.0.1.0, Revision=16#00000003.
    • Added AOM62 devdesc 1.0.3.0, Revision=16#00000001.
    • Added SIM61 devdesc 1.0.2.0, Revision=16#00000003.
    • Added SIM62 devdesc 1.0.2.0, Revision=16#00000003.
    • Added SIM63 devdesc 1.0.2.0, Revision=16#00000003.
    • Added SIM64 devdesc 1.0.2.0, Revision=16#00000001.
    • Added SIM65 devdesc 1.0.2.0, Revision=16#00000001.
    • Added Sys Util PCM61 library 1.0.0.0.

    Corrections

    • Fixed MIO21 devdesc 1.0.0.1, Revision=16#01000000.
    ]]>         iEx50 PLC CODESYS libraries - v2.0.15.0 https://deif-staging.jcdhotel.dk/software/iex50-plc-codesys-libraries/2-0-15-0/ 139917cd-78fd-4062-a2be-5f445c7a4df2 2025-12-29T00:00:00+00:00 software-version iEx50 PLC CODESYS libraries 2.0.15.0 current ## [2.0.15.0] - 2025-12-17

    Changes

    • Databases updated to version 2.0.15.0.
    ]]>         iEx50 CODESYS TSP (SP21) - v1.3.7.1 (SP21) https://deif-staging.jcdhotel.dk/software/iex50-codesys-tsp/1-3-7-1-sp21/ fe1263d6-8be1-4545-aa25-343d600abbe0 2025-11-04T00:00:00+00:00 software-version iEx50 CODESYS TSP (SP21) 1.3.7.1 (SP21) current ## [1.3.7.1] - 2025-10-13

    Improvements

    • Upgrade to CODESYS Runtime System version 3.5.21.10.

    Changes

    • Added AIO6·1 devdesc v 1.0.4.0, Revision = 16#00000006.
    • Added AIO6·2 devdesc v 1.0.4.0, Revision = 16#00000002.
    • Added AIM6·1 devdesc v 1.0.4.0, Revision = 16#00000002.
    • Added AIM6·2 devdesc v 1.0.4.0, Revision = 16#00000002.
    • Added AOM6·2 devdesc v 1.0.4.0, Revision = 16#00000002.

    ## [1.3.7.0] - 2025-09-18

    Improvements

    • Upgrade to CODESYS Runtime System version 3.5.21.10.

    Changes

    • Added GAM3.2 devdesc v 2.0.1.0, Revision = 16#02000100.
    • Push analog value to local I/O on every CODESYS iteration.
    • Rewrote analogue I/O tests to support faster DDS.
    ]]>         CODESYS IDE V3.5 SP21 - v3.5.21.10 (SP21) https://deif-staging.jcdhotel.dk/software/codesys-ide-v35/3-5-21-10-sp21/ a08006f7-98cc-4332-89e5-9c7d5ba7077d 2025-08-12T00:00:00+00:00 software-version CODESYS IDE V3.5 SP21 3.5.21.10 (SP21) current Updated to CODESYS IDE V3.5 SP21 Patch 10.

    ]]>